A silver electric strike rests on a metal workbench beside digital calipers and a blue tray of white gloves, with a factory background and banner text reading Electric Strike Manufacturers: How Buyers Can Compare.
Electric Strike Manufacturers: How Buyers Can Compare Suppliers
November 11, 2026
Silver panic bar hardware for double doors shown on a reflective floor, with bold white and red text reading Panic Bars for Double Doors: What Buyers Must Check.
Panic Bars for Double Doors: What Buyers Must Check Before Ordering
November 13, 2026

Panic Bar Parts Diagram: How Buyers Identify the Right Components

November 12, 2026

Quick Answer

A panic bar parts diagram breaks the device into the components a buyer actually orders: the bar or touch pad, body, end caps, latch, strike, mounting fixings, dogging control, outside trim and, on vertical models, rods and top or bottom locking points. Read the device family first, then match each part by position and measurement rather than appearance. OUBAO covers one-point, touch-bar and two-point layouts in stainless steel and painted finishes, which makes like-for-like comparison easier.

What Does a Panic Bar Parts Diagram Actually Show?

A panic bar parts diagram shows the device as an assembly, not a single SKU. Most diagrams divide it into the operating bar, the body or chassis that holds the mechanism, end caps, the latch, the frame strike, mounting brackets and fixings, the dogging control and any outside trim. Vertical models add upper and lower rods and separate top and bottom locking points.

That breakdown matters at quotation stage. A buyer replacing a complete device orders one model. A distributor supporting installations may need the exact latch, strike, end cap or fixing set. The panic bar parts diagram gives each item a position number so both sides discuss the same component.

Start with the device family. OUBAO’s panic exit device range separates horizontal bar, touch bar and vertical rod layouts, which is the first fork in any parts conversation.

The Parts That Drive Panic Bar Cost

The bar length, latch and strike arrangement, material and finish, dogging function and outside trim usually drive the commercial difference. A longer bar or a vertical pair uses more material and more parts. A stainless body costs more than a painted steel one. Dogging adds a mechanism. Outside trim adds a separate assembly.

The panic bar parts diagram makes those cost drivers visible line by line, so a buyer can compare scope instead of a single bottom-line figure.

That is why two quotes for a “panic bar” can sit far apart without either supplier being wrong. One may price a basic one-point bar; the other may include a full-length bar, stainless latch, strike and outside access device.

Ask for the quote by component and by variant. The answer shows whether the difference is real or just a different scope.

Touch Bar vs Crossbar: Match the Format First

A touch bar is a shallow pad that releases the latch with light pressure anywhere along its face. A crossbar is a deeper horizontal tube that the user pushes. Both are horizontal, but they feel different, look different and use different replacement parts.

Use the panic bar parts diagram to match the bar type before comparing finish or price. A touch-bar kit and a crossbar kit are not interchangeable.

The DK350 is a one-point crossbar device with a 900 mm oval bar, a lateral locking point and a stainless steel latch. It is non-handed and comes as DK-350P in painted steel or DK-350S in SS304. The 331P/331S uses a 1,000 mm tube, with a painted metal body on the P variant and SUS304 on the S variant. The 1710S/1710P is a touch bar with a 500 mm bar and 1,045 mm overall length. Both 1710 variants are 3-hour fire rated and hold a CE certificate from INTERTEK.

331P/331S – Horizontal Cross Bar Exit Device
  • Material — 331P: Metal body, Iron tube Material — 331S: SUS304 die casting cover, SUS304 body
View Product
Silver panic bar hardware with a long horizontal bar connecting two curved end brackets, shown on a white background.

For a buyer, the practical question is which format your market already sells and which one your installers can service. A like-for-like replacement should match the bar type before the finish.

Latch, Strike or Bolt: Which Part Are You Replacing?

The latch is the moving part on the device. The strike, sometimes called a striker, is the fixed keeper on the frame or threshold. A bolt is the locking element at the top or bottom of a vertical device.

A useful panic bar parts diagram names the latch, strike and bolt separately because they solve different problems and carry different measurements.

If the door does not stay closed, the latch or strike may be worn or misaligned. If the bar moves but the door will not release, the linkage or latch travel is the likely area. If a vertical device fails at one end, check that end’s bolt and striker before replacing the whole bar.

Naming the part correctly shortens the quote. “The latch does not catch” and “the strike is loose” point to different components, different measurements and sometimes different site work.

Which Parts Are Handed, and Which Are Not?

Handing describes which side the door hinges on. Many panic bars are non-handed, so the same device fits left- and right-hand doors. That reduces stock keeping units for a distributor.

OUBAO’s DK350, 1710S/1710P, 1720S/1720P and UL500P/UL500S are non-handed. The complete opening can still include position-specific parts: outside trim, strikes, rods and fixings may differ by side or by leaf. Confirm the full bill of materials rather than treating a non-handed bar as proof that every part is universal.

Mark the position-specific parts on the panic bar parts diagram for each opening, even when the operating bar itself fits either hand.

What Changes on a Vertical Rod or Two-Point Device?

A vertical device carries the release from the bar to locking points above and below. The panic bar parts diagram therefore needs to identify upper and lower tubes, the top and bottom bolts or latches, their strikers and the end caps. Installation checks grow too: header depth, floor or sill condition and straight rod travel.

The 1720S/1720P is a two-point vertical device with a 500 mm push bar, 1,045 mm overall length and 900 mm upper and lower tubes. Its standard maximum door height is 2,160 mm. Both variants are 3-hour fire rated and hold a CE certificate from INTERTEK. The 1720S uses SUS304 for the body, upper bolt, upper striker and end cap. The 1720P uses an aluminum alloy cover, steel body, stainless steel tube and steel end cap.

1720S/1720P – Two Points Locking Vertical Type Panic Bar
  • Material — 1720S: SUS304 Body Material — 1720P: Aluminum alloy cover, Steel Body, SS tube
View Product
Silver metal panic bar assembly with a long rectangular push rail and two curved end brackets connected by thin rods.

A one-point bar and a two-point device are not interchangeable parts sets. Read the diagram at the family level first.

On this family, the panic bar parts diagram should show both ends of the assembly, not just the push bar. That gives the buyer a complete replacement scope.

How Do You Match a Part Number to the Right Replacement?

Use four references: the model plate on the device, the diagram position number, a photo with a tape measure, and the finish or material code. The model plate identifies the family and variant. The position number identifies the component. The photo confirms the installed orientation. The code prevents a stainless part being ordered for a painted unit, or the reverse.

Measure the bar, the overall assembly and the mounting hole spacing. Record the door thickness and the frame strike position. If the label is missing, send photos of both ends, the latch, the strike and the full bar.

A supplier can then compare the parts against the current drawing instead of guessing from a catalogue image. That is faster than ordering a sample to find out.

A panic bar parts diagram supports that comparison only when it is paired with the installed device. The model plate, position number, photo and material code should all point to the same variant.

Metal panic bar hardware diagram with four panels for model, part name, photos and measurements, and material and finish.

Three Common Diagram Misreads

Three mistakes recur. The first is reading “bar length” as “door width.” A 900 mm bar is a component dimension, not a statement that every 900 mm door suits the device. The second is mixing the latch and the strike when describing a fault. The third is treating an option as standard, especially dogging and outside trim.

Those errors usually begin when the panic bar parts diagram is read as a picture rather than a bill of materials. Read the labels, measurements and variant codes together.

Dogging holds the latch retracted so people can pass without pressing the bar each time. The UL500P/UL500S includes a dogging function, a 500 mm bar and a 1,045 mm overall length. It is UL Listed under SA44924 with a 1.5-hour fire rating. On a fire-rated opening, match the intended use of dogging to the door assembly’s approval before you specify it.

Outside trim is the handle, key or access-control interface on the outside face. It is a separate selection from the inside bar, even when a catalogue shows them together.

Which Parts Should a Distributor Keep in Stock?

Stock the parts that fail or go missing most often in your own installations, not a generic list. Ask the supplier which components are available separately, then compare that list with your service history. End caps, latches, strikers and fixing packs are common candidates, but the right mix depends on the models you sell.

For a private-label range, keep the finish code and packaging consistent across spare parts. A replacement end cap in a different shade creates a visible mismatch and a return.

Pair the panic bar parts diagram with your own failure and replacement history. That shows which components deserve shelf space and which can stay on demand.

Panic Bar Parts RFQ Checklist

Send the device model and variant, the diagram position number or part name, the quantity and the finish. Add door type, leaf width and weight, mounting method and photos of the installed device. State the target market and the documents you need. If the part is for a fire-rated opening, include the door assembly details so the replacement can be checked in context.

Annotate the panic bar parts diagram with the positions you need, then attach it to the RFQ. The supplier can quote the exact component set without translating a list of descriptions.

OUBAO has made door-control hardware since 1987 and produces exit devices alongside door closers and magnetic locks at its 106,000 m² base in Lishui, Zhejiang. For a parts request, the team can review the model drawing and confirm the variant, material and available documents. Send the details through the contact page, or use the FAQ page to check what information the team needs for a configuration review.

Final Thoughts / Next Step

A panic bar parts diagram is most useful when you read it in the right order: device family, then bar type, then locking points, then the individual part. That sequence prevents the common errors of matching by photo, confusing latch with strike, or ordering an option that was never included.

For a quotation, send OUBAO the door type, leaf width and weight, installation method, target market, required documents and estimated quantity. The team can then confirm the right model and component set.

Hi, welcome to OUBAO.
This article comes from the OUBAO Team, drawing on our long experience in door control hardware and real-world manufacturing projects. We hope the information below gives you a clearer and more practical way to look at this topic.
Exploring a specific project or have a question along the way? We’d be happy to share our thoughts.
OUBAO door control manufacturer

Share This Page

Get a Quote

    Related Posts

    There are no posts on the list.
    ✕

      Find the right door control solution.

      Looking for door closers or magnetic locks for your product range? Tell us what you need, and our team can help with product options, OEM/ODM requirements and supporting documents.

      ProductsDoor closers & magnetic locks

      ServicesOEM & ODM

      CertificatesUL, CE, ANSI, EN 1154, EN 1634

      Send an inquiry