Quick Answer
A panic bar for double doors is not simply two single-door bars ordered in the same finish. Decide whether both leaves must release together, which leaf carries the main latch, and whether the pair needs a vertical-rod or horizontal-bar arrangement. Then check overlap, frame stops, strike points, outside trim and leaf size before comparing models or prices. OUBAO’s 1710S/1710P, 331P/331S and two-point 1720S/1720P give buyers useful starting points, but the complete opening should drive the quote.
Why Not Just Order Two Single-Door Panic Bars?
A double door is one opening with two leaves, not two independent doors placed side by side. The leaves meet at the center, share a closing sequence and often overlap. Hardware chosen for one leaf can collide with the other, miss its strike or leave one side unable to release cleanly. That is why a panic bar for double doors starts with the pair layout, not a quantity of two.
The buyer’s first job is to define the opening. Which leaf opens in normal use? Does the other leaf stay secured until someone releases it? Must a single push release both leaves, or does each leaf have its own device? These answers decide the hardware set more than the finish or model name.
The panic exit device range includes horizontal and vertical formats. That range is useful only after the opening is described clearly. A supplier can then recommend a format that matches the leaf arrangement instead of quoting two bars that happen to look alike.
Which Leaf Opens First, and Which One Carries the Lock?
The active leaf usually opens first and carries the main operating hardware. The inactive leaf is the secondary leaf, often held at the top and bottom. Many pairs are arranged this way, but the sequence should come from the door design and the required evacuation plan, not from habit.
Active Leaf vs Inactive Leaf
The active leaf is the one people use every day. It may carry the main panic bar, latch and outside trim. The inactive leaf normally stays closed and may be secured by top and bottom bolts. In an emergency, the active leaf opens first, followed by the inactive leaf.
The buying question is whether that sequence still gives a clear exit. If the inactive leaf must also release on a push, the pair needs hardware that supports that operation. If it only opens after the active leaf, the supplier needs to know the intended sequence before selecting bolts, strikes and connecting parts.
This is also where handing and stock planning matter. Handing means which side the door hinges on. The 1710, 331 and 1720 devices are non-handed, which can simplify inventory across left- and right-hand doors. The complete pair may still include handed or position-specific parts, so confirm the full bill of materials rather than only the bar.
Why the Overlap Detail Changes the Hardware Set
Overlap is the distance one leaf sits in front of the other when the doors are closed. A projecting bar, closer arm, pull or outside trim can reduce clearance at that meeting point. If the hardware is chosen from a catalog image alone, it may fit the leaf but foul the other leaf.
Send a photo of the closed meeting edges and a measurement of the overlap or center gap. Include the frame stop and the face clearance on both leaves. These details tell the supplier whether the devices can sit side by side or whether the pair needs a different arrangement.
Choosing a Vertical-Rod Pair
Use a vertical-rod double door exit device when the leaf needs locking points at the top and bottom, or when the design has no fixed mullion for a horizontal latch to engage. Use a horizontal bar when a single lateral locking point suits the opening and the frame or meeting stile provides a sound strike position.
A vertical-rod device carries rods above and below the bar. The upper rod latches into the header, and the lower rod latches at the floor or sill. This arrangement can suit tall or heavy leaves because the locking points are spread across the door height. It also brings more installation checks: header depth, floor condition, sill clearance and straight rod travel.
For a two-point vertical arrangement, OUBAO’s 1720S/1720P uses 900 mm upper and lower tubes and has a standard maximum door height of 2,160 mm. The 1720S has a SUS304 stainless steel body; the 1720P has an aluminum cover, steel body and stainless steel tube. Both are two-point vertical devices and non-handed.
- Material — 1720S: SUS304 Body Material — 1720P: Aluminum alloy cover, Steel Body, SS tube

For comparison, the DK350 one-point push bar has a lateral locking point and a 900 mm oval bar. It is a useful reference for a single-point horizontal layout, but it is not a pair kit. Do not treat one bar as a complete double-door specification.
Horizontal Bar or Vertical Rod: A Buyer’s Comparison
| Decision point | Horizontal bar | Vertical rod |
|---|---|---|
| Locking points | One lateral point | Top and bottom points |
| Frame requirement | Sound strike position | Header and floor/sill conditions |
| Main installation check | Bar clearance and strike alignment | Rod travel and floor clearance |
| Good starting question | Is one locking point enough? | Does the leaf need two-point locking? |
The table narrows the conversation. It does not replace a door survey or the supplier’s review of the complete opening.
Overlap, Mullion, and Strike Points
A mullion is the vertical member between the leaves. A fixed mullion can provide a stable strike position for a horizontal bar. A removable mullion may be taken out for a wider clear opening, which changes how the doors are secured. A pair with no mullion relies on the meeting stile, an astragal (a strip that covers the meeting edges) or vertical locking points instead.
Strike points are the places where the latch or bolt engages. On a pair, one leaf may strike into the other leaf, the frame or the floor and header. Each point must line up through the full swing. If the doors have dropped, the frame is out of square or the sill is uneven, a device that works on the bench can still bind after installation.
Dimensions to send with the inquiry include:
- Leaf width, height and thickness for both doors.
- Door material, core and estimated leaf weight.
- Overall clear opening and the center gap or overlap.
- Frame material, depth and stop position.
- Header and floor/sill details for vertical rods.
- Hinge side, swing direction and push face.
- Outside trim, closer, coordinator or access-control hardware already specified.

Measure each leaf separately. A pair can look symmetrical while the two leaves differ after site adjustments. Photos with a tape measure in frame are more useful than a written description on its own.
Which Models Should You Compare?
Start with the device format, then compare materials and dimensions. The 1710, 331 and 1720 families cover horizontal touch bar, horizontal crossbar and two-point vertical layouts, so they answer different opening questions.
For a horizontal touch bar, the 1710S/1710P has a 500 mm push bar and 1,045 mm overall length. The 1710S uses SUS304 for the cover and body; the 1710P uses an aluminum alloy cover with a steel body and a silver painted finish. Pressure on the touch bar withdraws the latch, and the model is non-handed.
- Material — 1710S: SUS304 die casting cover, SUS304 body Material — 1710P: Aluminum alloy cover, Steel Body

For a horizontal crossbar, the 331P/331S uses a 1,000 mm tube. The 331S has a SUS304 die-cast cover and body. The 331P has a painted metal body and iron tube. It is also non-handed, and pressure on the tube withdraws the latch.
For a pair that needs top-and-bottom locking points, compare the 1720S/1720P described above. Its 500 mm push bar and 1,045 mm overall length match the 1710 figures, while the 900 mm rods and 2,160 mm standard maximum door height make it a different installation proposition.
All three families use timber-door fixings as standard, with metal-door fixings available. They are compatible with an outside access device, so exterior entry hardware can be planned with the exit device rather than added after the door is prepared.
Material choice is a commercial decision as well as a visual one. SUS304 versions suit buyers who want a stainless finish across the range. Painted versions can serve price-sensitive projects or interiors where a matching paint finish matters. Confirm the finish on the exact variant, especially when both leaves must look identical.
Checking the Assembly Before Ordering
Build a one-page opening schedule and ask the supplier to mark the hardware on a door elevation. The drawing should show both leaves, the bar positions, rod or latch locations, strike points, outside trim and the direction of escape. A clear drawing catches most coordination problems before they become shipping or installation costs.
Then check the assembly in three positions: doors closed, doors partly open and doors at full swing. Look for interference at the meeting edges, frame stops and floor. Confirm that the inactive leaf can be released in the intended sequence and that the active leaf clears the other leaf throughout its travel.
Ask for the installation instructions and the model-specific document set for the destination market before the order is released. If the opening is part of a larger project, compare the exit devices with the closers, stops and access control on the same schedule. The FAQ page is a practical place to confirm what information the team needs for a configuration review.
Double-Door Panic Bar Quote Checklist
A useful double door panic bar quote reads like an installation plan, not a single price line. It should list the device for each leaf, the material and finish, bar or rod lengths, strikes, fixings and outside trim. It should also state the quantity, packing method and the documents included for the target market.
Ask the supplier to identify any part that is shared between the leaves and any part that is position-specific. Confirm spare fixings, fasteners for the actual door material and the finish code. For a distributor, this level of detail makes it easier to stock the right variants and avoid site returns.
The same rule applies to samples. A sample bar confirms the look and feel; it does not prove that the complete pair will fit the opening. Send the door schedule with the sample request so the supplier can check the configuration as a system.
Final Takeaway: Specify the Opening, Then the Hardware
A panic bar for double doors should be selected as part of one opening. Define the active and inactive leaves, the release sequence, the overlap or center gap, the strike points and the frame conditions before comparing models. Then choose between a horizontal bar and a vertical-rod arrangement and confirm the exact variant, finish and fixings.
OUBAO can review the pair against the door details and help narrow the model. Send the door type, leaf width and weight, installation method, target market, required documents and estimated quantity through the contact page. The team can then confirm the configuration and prepare a quotation for the complete opening.



