OUBAO booth at Canton Fair 2026, featuring door closer displays and buyers meeting with the team.
OUBAO at the 140th Canton Fair: Door Control Products and Exhibition Highlights
October 23, 2026
A silver door closer with an articulated arm on a wooden workbench beside rolled blueprints, a yellow tape measure, and a white hard hat, with construction site text overhead.
Commercial Door Closer Installation: A Practical Guide for Contractors
November 2, 2026

180 Degree Door Closers: 6 Checks Before You Specify One

November 1, 2026

Quick Answer

A 180 degree door closer is not one product type. First decide whether the door must swing to 180°, hold open at 180°, or both. Then check wall and hinge clearance, arm and mounting, power size, fire-door approval, and the documents for the exact model. In many layouts, the arm and geometry matter more than a special closer. OUBAO’s 700 Series covers 15–120 kg leaves, and its OEM range offers 90–180° opening configurations. Specify that configuration clearly before you request a quote.

1. Define What 180 Degrees Means Here

A 180 degree door closer can mean three different things, and the price and lead time change with each one. On a single-leaf door, 180° is usually the position where the leaf finishes flat against the wall beside the opening. Whether the closer can take the door there, and whether it can keep it there, are separate questions.

Swing to 180°. A 180 degree door closer for swing-only use opens through the full arc and then closes normally. This is mainly a question of hinge position, wall clearance and arm travel. A standard closer can often allow this, but the arm, stop and frame decide the real limit.

Hold open at 180°. The closer keeps the leaf at 180° until someone releases it. That needs a hold-open arm made for the angle, or a separate hold-open device. A standard arm will not do the same job. The hold-open and non-hold-open comparison explains the difference in daily use.

A published maximum of 180°. The closer may be rated to open that far, but the installed door may stop earlier because of a wall, a door stop, a deep frame reveal or the selected bracket. Treat the catalogue angle as a starting point, not a promise for the finished opening.

Diagram comparing a door closer swinging to 180 degrees and holding open at 180 degrees, with top-view wall and door leaf diagrams, a silver door closer, and a note to check the arm or hold-open device.

Write the requirement in degrees and state whether it is swing-only or hold-open. Buyers often search for a door closer 180 degrees without separating the two, so that one line removes most of the ambiguity from a quotation.

2. Check the Door and Frame Swing Path

Measure the opening before comparing models. A 180 degree door closer cannot create clearance that the building does not have.

At 180°, the hinge edge of the leaf sweeps close to the wall and frame. Door thickness and hinge offset determine how much room the leaf needs. A thick leaf on a small offset can meet the wall before the closer reaches its limit. So can a deep frame reveal, a projecting door stop, a tall handle, a kick plate, a seal or a floor-mounted door closer.

Check the full swing path, not just the closed door. Look for walls, columns, radiators, pipework, adjacent doors and anything stored beside the opening. On a pair of doors, check the meeting stiles and the coordinator as well. A 180° door closer may be the correct hardware, but it will not compensate for a door that is already blocked at 160°.

Use an elevation and a plan detail through the hinge side. A photograph rarely shows the gap between the leaf and the wall at full opening. If the drawing shows less than 180°, ask the project team whether the requirement can be reduced before you price a special arm.

This is also where the 180 degree door closer opening angle affects cost. A standard mounting that reaches 180° is usually cheaper and faster to supply than a special bracket or a deeper frame modification.

3. Match the Arm and Mounting to the Angle

For a 180 degree door closer, the arm and mounting decide whether the door can reach 180° and whether it can stay there.

Standard arm. The body sits on the pull side of the door, and the arm folds against the door face. It is the common choice for a regular head frame and a clean swing.

Parallel arm. The body sits on the push side, and the arm runs roughly parallel to the door face when closed. It can suit a shallow header or a door that needs the closer out of the way, but the arm, bracket and stop must be checked against the full opening. The parallel arm guide covers the layout and adjustment points.

Top jamb. The body fixes to the frame header, with the arm reaching down to the door. It keeps the door face clearer but needs a suitable header and fixing position.

Slide arm or track. The arm runs in a track rather than a folding link. It can give a neater appearance and a controlled sweep, but the track position and door clearance still set the limit. On the 700 Series, models 704 and 705 accept slide arm installation as well as standard, parallel and top jamb mounting.

Hold-open adds another variable for a 180 degree door closer. Hold-open arms are made for a set angle or a limited range, so “hold-open” in a product description does not automatically mean 180°. Give the supplier the exact angle and ask for the matching arm. If the door only needs to swing to 180° and close again, say so; you may avoid paying for a hold-open function you do not need.

Parallel Arm Door Closer: When Should Commercial Buyers Specify It?
  • Specify a parallel arm door closer when there is no usable headroom above the door — a low ceiling, an exit sign, or conduit sitting where the closer body would normally go.
Read Article
Silver parallel arm door closer mounted beside a glass double door, with red and black text reading Parallel Arm Door Closer: When Should Commercial Buyers Specify It?

4. Is the Closer Sized for the Leaf at Full Opening?

Size a 180 degree door closer by leaf weight, leaf width and mounting, not by weight alone. Power size is the spring strength class, normally shown as EN 1–6; a higher number does not automatically mean a better fit for every door.

The 700 Series shows how the range steps up:

ModelPower sizeDoor weightDoor widthCertificates
701115–30 kg≤750 mmUL, UL 10C
702225–45 kg≤850 mmUL, UL 10C
703340–65 kg≤950 mmUL, UL 10C, CE
704465–85 kg≤1,100 mmUL, UL 10C, CE
705580–120 kg≤1,250 mmUL, UL 10C, CE

At 180°, the leaf has a long lever and is more exposed to wind and air-pressure differences across the building. A backcheck function cushions the last part of the opening swing; on the 700 Series it is optional on the 704 and 705. If the door opens onto a corridor with strong pressure, put that condition in the brief rather than simply moving up a power size.

700 Series Classic Door Closer, UL & CE Certified
  • This series is designed for various door types, including wooden and metal doors. Yes, this series features a non-handed design.
View Product
Silver door closer with a rectangular body, articulated arm, and threaded rod ending in a mounting bracket.

The 700 Series is non-handed, so one unit covers left- and right-hand doors. That reduces part numbers for a distributor, but the arm and mounting still need confirming.

Do not oversize the closer to fix a binding hinge, a weak frame or a door that is out of square. Correct the door first, then select the closer. The door closer size chart explains how width, weight and power size work together.

5. Confirm Fire and Egress Requirements

On a fire door, a 180 degree door closer is part of a tested door assembly. The model, arm and mounting must match the configuration covered by the test evidence, and a 180° hold-open is not a default choice.

In the 700 Series, the 701 and 702 carry UL and UL 10C listings. The 703, 704 and 705 carry UL, UL 10C and CE. The UL 10C listing covers the closer within the tested assembly, so specify the arm and installation that go with the model. If the project requires a 180° hold-open on a fire door, check the release device and door schedule together.

A fire-door schedule may require the leaf to close and latch without assistance. A hold-open arm that keeps the leaf at 180° usually needs an approved release, and some fire-door schedules do not permit hold-open at all. Check the door schedule and the local authority before you include that arm in the price.

Egress doors add a different check. The closer must not make the exit harder to use, and the door must still close and latch after each opening. A 180° swing can be useful in a hospital, hotel or corridor where beds, carts or luggage pass through, but the hardware still has to suit the traffic and the frame.

Ask for the certificate and test report for the exact model, arm and installation. The fire-rated door closer selection guide sets out the documents to request.

6. Is the Exact Configuration in the RFQ?

A 180° requirement is only useful when tied to the door, arm and documents. Put the full 180 degree door closer configuration in the RFQ, not just the phrase itself.

Include:

  • Leaf width, height, thickness, weight and material
  • Frame material and header depth
  • Hinge type and position
  • Mounting style: standard, parallel, top jamb or slide arm
  • Swing direction, or a non-handed requirement
  • Required opening angle and hold-open angle
  • Fire rating and test standard, where applicable
  • Finish, branding and packaging
  • Target market and required documents
  • Quantity and delivery schedule

State the angle in degrees and separate swing from hold-open. Say whether the door must stop at 180° or simply pass through it. Add a drawing if the wall, frame or adjacent door is unusual.

That package lets the supplier quote a complete 180 degree door closer set with matching arm and bracket. It also gives you a clear baseline for samples, inspection and repeat orders. For private-label programmes, OUBAO’s OEM/ODM process can take the door schedule, target angle and document requirements into the quotation.

Which OUBAO Closer Should You Shortlist?

For a 180 degree door closer project, start with the 700 Series classic door closer for surface-mounted commercial doors in the 15–120 kg range. Move to the OEM/ODM programme when the leaf, width or opening angle falls outside the standard range.

OUBAO is a China-based manufacturer of door closers, magnetic locks and related door-control hardware. The door closer range includes surface and concealed models, so a buyer can compare mounting styles before choosing a series.

The 700 Series runs from the 701 at power size 1 to the 705 at power size 5. All five models have adjustable closing and latching speed, and all are non-handed. Hold-open is optional on the 701, 702 and 703; backcheck is optional on the 704 and 705. Models 704 and 705 cover the widest leaves and also accept slide arm installation.

For a project outside that range, OUBAO’s OEM/ODM selection covers opening angles from 90° to 180°, standard or hold-open arms, door weights up to 300 kg and widths up to 1,600 mm, with EN 1–6 spring power. That breadth helps a distributor build a range, but each configuration still needs its own model, arm and document check.

Final Thoughts / Next Step

The six checks for a 180 degree door closer follow one order: define what 180° means, confirm the door can reach it, match the arm and mounting, size the closer, check the fire and egress requirement, then put the exact configuration in the RFQ. Buyers who skip the first two often pay for a special arm they do not need, or discover at installation that the wall stops the door first.

Send OUBAO the door type, leaf weight and width, mounting method, target opening angle, target market, required documents and order quantity. The team can confirm a suitable model, arm and quotation. Start with the contact page.

Hi, welcome to OUBAO.
This article comes from the OUBAO Team, drawing on our long experience in door control hardware and real-world manufacturing projects. We hope the information below gives you a clearer and more practical way to look at this topic.
Exploring a specific project or have a question along the way? We’d be happy to share our thoughts.
OUBAO door control manufacturer

Share This Page

Get a Quote

    Related Posts

    There are no posts on the list.
    ✕

      Find the right door control solution.

      Looking for door closers or magnetic locks for your product range? Tell us what you need, and our team can help with product options, OEM/ODM requirements and supporting documents.

      ProductsDoor closers & magnetic locks

      ServicesOEM & ODM

      CertificatesUL, CE, ANSI, EN 1154, EN 1634

      Send an inquiry